EVM PROGRAMMING FOR LUCENT PROLOGIX
| EVM PROGRAMMING ITEM | EVM PROGRAMMING DATA | EXPLANATION |
| For op / ext ring duration during working / closing hrs | SYS _ 2 _ 2 _ [00],SYS _ 2 _ 3 _ [00] SYS _ 2 _ 4 _ [00],SYS _ 2 _ 5 _ [00] | Un-supervisory ringback tone |
| For release after answer | SYS _ 5 _ 2 _ [5] | ON HOOK |
| For release w / o waiting | SYS _ 5 _ 3 _ [5] | ON HOOK |
| For retrieving call once error tone | SYS _ 5 _ 4 _ [3] | HOOK FLASH + HOOK FLASH |
| For retrieving call once on busy | SYS _ 5 _ 5 _ [3] | HOOK FLASH + HOOK FLASH |
| For retrieving call once no answer | SYS _ 5 _ 6 _ [3] | HOOK FLASH + HOOK FLASH |
| For message lamp on | SYS _ 5 _ 7 _ [8] | Function code + Extn |
| For message lamp off | SYS _ 5 _ 8 _ [8] | Function code + Extn |
| For no-answer identified code ( For External no-answer forward ) | SYS _ 6 _ 3 _ [ Function code ] | Refer to PBX programming |
| For code of message lamp on | SYS _ 6 _ 6 _ [ Function code ] | Refer to PBX programming |
| For code of message lamp off | SYS _ 6 _ 7 _ [ Function code ] | Refer to PBX programming |
| For hook flash time | SYS _ 7 _ 1 _ [By auto detection ] | Refer to EVM GUIDE: How to auto detect hook flash time |
| For busy tone cycle | SYS _ 7 _ 5 _ 1 _ [051] SYS _ 7 _ 5 _ 2 _ [041] SYS _ 7 _ 5 _ 3 _ [051] SYS _ 7 _ 5 _ 4 _ [041] Data in [ ] is just a reference | Refer to EVM GUIDE : How to auto detect busy tone cycle |
| For ringback tone cycle | SYS _ 7 _ 6 _ 1 _ [113] SYS _ 7 _ 6 _ 2 _ [373] SYS _ 7 _ 6 _ 3 _ [113] SYS _ 7 _ 6 _ 4 _ [373] Data in [ ] is just a reference | Refer to EVM GUIDE: How to auto detect ringback tone cycle |
| Waiting time for ID code | ADM _ 5 _ 9908 _ [ 0000 ] | Delay 0.5 sec before detecting ID code |
| Prefix number of Mailbox ID code | ADM _ 5 _ 9920 _ [Function code] | Refer to PBX programming |
| Suffix number of Mailbox ID code | ADM _ 5 _ 9921 _ [ *1 *1 ] | Suffix number of Mailbox ID code is # # |
| For no-answer identified code ( For Internal no-answer forward ) | ADM _ 5 _ 9928 _ [Function code] | Refer to PBX programming |
PBX PROGRAMMING:
Set port of EVM as VMI
Chang system parameters mode code page 1
MODE CODE RELATED SYSTEM PARAMETERS
MODE CODE ( FROM SWITCH TO VMS )
Direct inside Access : Set Function code for Prefix number of Mailbox ID code
( Must be set only in 1 digit)
Direct Dial Access - Trunk: Delete
Internal Coverage: Set Function code for no-answer identified code
External Coverage: Set Function code for no-answer identified code
DTMF Duration on (msec): 100 off (msec) : 100 Sending Delay (msec) : 500
Example :
If 8 is set for Direct inside Access code of PBX, then PBX will send out 8 # + Calling number + # # to VMS.
EVM Programming must be set as ADM _ 5 _ 9920 _ [ 8*1 ]
EVM Programming must be set as ADM _ 5 _ 9921 _ [ *1 *1 ]
If * 7 is set for Internal Coverage, then PBX will send out * 7 + # + Calling number + # + Called number + # to VMS.
EVM Programming must be set as ADM _ 5 _ 9928 _ [ **707 ] Note : If Calling number is in 3 digits
EVM Programming must be set as ADM _ 5 _ 9928 _ [ **708 ] Note : If Calling number is in 4 digits
If * 8 is set for External Coverage, then PBX will send out * 8 + # # + Calling number + # # to VMS.
EVM Programming must be set as SYS _ 6 _ 3 _ [ **804 ]
Set no-answer forward to Extn of EVM for All Extension.