EVM  PROGRAMMING FOR NEC - M100 / M80

EVM  PROGRAMMING  ITEMEVM  PROGRAMMING  DATA                EXPLANATION
For  op / ext ring duration during
working / closing hrs		SYS _ 2 _ 2 _ [00],SYS _ 2 _ 3 _ [00]
SYS _ 2 _ 4 _ [00],SYS _ 2 _ 5 _ [00]		Un-supervisory ringback tone                  
For release after answerSYS _ 5 _ 2 _ [5]ON HOOK
For release w / o waitingSYS _ 5 _ 3 _ [5]ON HOOK
For retrieving call once error toneSYS _ 5 _ 4 _ [1]HOOK FLASH
For retrieving call once on busySYS _ 5 _ 5 _ [1]HOOK FLASH
For retrieving call once no answerSYS _ 5 _ 6 _ [1]HOOK FLASH
For message lamp onSYS _ 5 _ 7 _ [8]Function code + Extn
For message lamp offSYS _ 5 _ 8 _ [8]Function code + Extn
For no-answer identified codeSYS _ 6 _ 3 _ [ Function code ]Refer to PBX programming
For code of message lamp onSYS _ 6 _ 6 _ [ Function code ]Refer to PBX programming
For code of message lamp offSYS _ 6 _ 7 _ [ Function code ]Refer to PBX programming
For hook flash timeSYS _ 7 _ 1 _ [By auto detection ]Refer to EVM GUIDE:
How to auto detect hook flash time
For error tone cycleSYS _ 7 _ 4 _ 1 _ [022]
SYS _ 7 _ 4 _ 2 _ [022]
SYS _ 7 _ 4 _ 3 _ [022]
SYS _ 7 _ 4 _ 4 _ [022]
Data in [ ] is just a reference		Refer to EVM GUIDE:
How to auto detect error tone cycle
For busy tone cycleSYS _ 7 _ 5 _ 1 _ [048]
SYS _ 7 _ 5 _ 2 _ [045]
SYS _ 7 _ 5 _ 3 _ [048]
SYS _ 7 _ 5 _ 4 _ [045]
Data in [ ] is just a reference		Refer to EVM GUIDE:
How to auto detect busy tone cycle
For ringback tone cycleSYS _ 7 _ 6 _ 1 _ [096]
SYS _ 7 _ 6 _ 2 _ [280]
SYS _ 7 _ 6 _ 3 _ [096]
SYS _ 7 _ 6 _ 4 _ [280]
Data in [ ] is just a reference		Refer to EVM GUIDE:
How to auto detect ringback tone cycle
Waiting time for ID codeADM _ 5 _ 9908 _ [ 0000 ]Delay 0.5 sec before detecting ID code

PBX PROGRAMMING:
Set YY = 03 in COMMAND  13      [ ALL EXTN ] must be set to [ 0 ]
Set YY = 10 in COMMAND  13      [EXTN OF EVM ] must be set to [ 0 ]
Set [ 0 ] in YY = 333 of COMMAND  08  
Set NO ANSWER IDENTIFIED CODE ( MUST 2 DIGITS )  for  CODE = 3 of YY = 00 of COMMAND  50
Set [ 00 ] for FUNCTION NUMBER = 44 of Y = 0 of COMMAND  41       
Set [ 02 ] for FUNCTION NUMBER = 48 of Y = 0 of COMMAND  41        
Set [ 07 ] for FUNCTION NUMBER = 49 of Y = 0 of COMMAND  41      
Set FUNCTION CODE OF MESSAGE LAMP  ON for FUNCTION CODE = 040  of Y = 0 of COMMAND 20
Set FUNCTION CODE OF MESSAGE LAMP OFF  for FUNCTION CODE = 041 of Y = 0 of COMMAND 20  
Set to STATION HUNTING GROUP for [ EXTN OF EVM ] of Y = 0 of COMMAND  18    
Set [ 04 ] for [ TRUNK NUMBER ] of YY = 02 of COMMAND 30       
Set [ EXTN OF EVM PORT1 ] for [ TRUNK NUMBER ]  of YY = 04 of COMMAND 30