EVM PROGRAMMING FOR PANASONIC KX-TD1232
EVM PROGRAMMING ITEM | EVM PROGRAMMING DATA | EXPLANATION |
For op / ext ring duration during working / closing hrs | SYS _ 2 _ 2 _ [00],SYS _ 2 _ 3 _ [00] SYS _ 2 _ 4 _ [00],SYS _ 2 _ 5 _ [00] | Un-supervisory ringback tone |
For release after answer | SYS _ 5 _ 2 _ [5] | ON HOOK |
For release w / o waiting | SYS _ 5 _ 3 _ [5] | ON HOOK |
For retrieving call once error tone | SYS _ 5 _ 4 _ [1] | HOOK FLASH |
For retrieving call once on busy | SYS _ 5 _ 5 _ [1] | HOOK FLASH |
For retrieving call once no answer | SYS _ 5 _ 6 _ [1] | HOOK FLASH |
For message lamp on | SYS _ 5 _ 7 _ [8] | Function code + Extn |
For message lamp off | SYS _ 5 _ 8 _ [8] | Function code + Extn |
For directly pick up | SYS _ 5 _ 8 _ [8] | Function code + Extn |
For no-answer identified code | SYS _ 6 _ 3 _ [ *1602 ] | No Answer identified code is #6 |
For code of message lamp on | SYS _ 6 _ 6 _ [ 701 ] | Function code of message lamp on is 701 ( PBX Default ) |
For code of message lamp off | SYS _ 6 _ 7 _ [ 700 ] | Function code of message lamp off is 700 ( PBX Default ) |
For hook flash time | SYS _ 7 _ 1 _ [By auto detection ] | Refer to EVM GUIDE: How to auto detect hook flash time |
For error tone cycle | SYS _ 7 _ 4 _ 1 _ [026] SYS _ 7 _ 4 _ 2 _ [022] SYS _ 7 _ 4 _ 3 _ [026] SYS _ 7 _ 4 _ 4 _ [022] Data in [ ] is just a reference | Refer to EVM GUIDE: How to auto detect error tone cycle |
For busy tone cycle | SYS _ 7 _ 5 _ 1 _ [051] SYS _ 7 _ 5 _ 2 _ [045] SYS _ 7 _ 5 _ 3 _ [051] SYS _ 7 _ 5 _ 4 _ [045] Data in [ ] is just a reference | Refer to EVM GUIDE: How to auto detect busy tone cycle |
For ringback tone cycle | SYS _ 7 _ 6 _ 1 _ [051] SYS _ 7 _ 6 _ 2 _ [019] SYS _ 7 _ 6 _ 3 _ [051] SYS _ 7 _ 6 _ 4 _ [261] Data in [ ] is just a reference | Refer to EVM GUIDE: How to auto detect ringback tone cycle |
For code of directly pick up | ADM _ 5 _ 9907 _ [ 41 ] | Function code of directly pick up is 41 ( PBX Default ) |
Waiting time for ID code | ADM _ 5 _ 9908 _ [ 2000 ] | Delay 2 sec before detecting ID code |
PBX PROGRAMMING:
Setting steps for Programming address [ 602 ]: 1. enter "Jack no of EVM" 2. assign to the Same Extension Group
Setting steps for Programming address [ 106 ]: 1. assign AA Station Hunting Type to Extension Group of EVM
Setting steps for Programming address [ 113 ]: VM Status DTMF Set
1. delete DTMF in RBT Status 2. delete DTMF in BT Status 3. delete DTMF in ROT Status 4. delete DTMF in DND Status 5. delete DTMF in ANSWER Status 6. delete DTMF in Disconnect Status
Setting steps for Programming address [ 114 ]: VM Command DTMF Set
1. delete GETMSG DTMF in VM command 2. set to [#6] ( Default ) from VM-SVC DTMF in VM command
Setting steps for Programming address [ 990 ]: Set to [00] in Field [ 7 ]
Setting steps for Programming address [ 407 ]: 1. enter "CO line number" 2. enter "Extn of EVM" ( Set Incoming ring of CO line to Extn of EVM)
Set No Answer Forward To Extn of EVM for All Extension