EVM  PROGRAMMING FOR TECOM SD - 500 / SD - 700

EVM  PROGRAMMING  ITEMEVM  PROGRAMMING  DATA                EXPLANATION
For  op / ext ring duration during
working / closing hrs		SYS _ 2 _ 2 _ [00],SYS _ 2 _ 3 _ [00]
SYS _ 2 _ 4 _ [00],SYS _ 2 _ 5 _ [00]		Un-supervisory ringback tone                  
For release after answerSYS _ 5 _ 2 _ [5]ON HOOK
For release w / o waitingSYS _ 5 _ 3 _ [5]ON HOOK
For retrieving call once error toneSYS _ 5 _ 4 _ [1]HOOK FLASH
For retrieving call once on busySYS _ 5 _ 5 _ [1]HOOK FLASH
For retrieving call once no answerSYS _ 5 _ 6 _ [1]HOOK FLASH
For message lamp onSYS _ 5 _ 7 _ [8]Extn + Function code
For message lamp offSYS _ 5 _ 8 _ [8]Function code + Extn
For directly pick upSYS _ 5 _ 9 _ [9]Extn +  Function code
For no-answer indentified code
( For no-answer forward )		SYS _ 6 _ 3 _ [ Function code ]Refer to PBX Programming
For busy indentified code
( For busy forward  )		SYS _ 6 _ 4 _ [ Function code ]Refer to PBX Programming
For code of message lamp onSYS _ 6 _ 6 _ [ *196 ]Function code of message lamp on is
#96
For code of message lamp offSYS _ 6 _ 7 _ [ *1**96 ]Function code of message lamp off is
#*96
For hook flash timeSYS _ 7 _ 1 _ [By auto detection ]Refer to EVM GUIDE:
How to auto detect hook flash time
For error tone cycleSYS _ 7 _ 4 _ 1 _ [022]
SYS _ 7 _ 4 _ 2 _ [019]
SYS _ 7 _ 4 _ 3 _ [022]
SYS _ 7 _ 4 _ 4 _ [019]
Data in [ ] is just a reference		Refer to EVM GUIDE:
How to auto detect error tone cycle
For busy tone cycleSYS _ 7 _ 5 _ 1 _ [048]
SYS _ 7 _ 5 _ 2 _ [045]
SYS _ 7 _ 5 _ 3 _ [048]
SYS _ 7 _ 5 _ 4 _ [045]
Data in [ ] is just a reference		Refer to EVM GUIDE:
How to auto detect busy tone cycle
For ringback tone cycleSYS _ 7 _ 6 _ 1 _ [106]
SYS _ 7 _ 6 _ 2 _ [200]
SYS _ 7 _ 6 _ 3 _ [106]
SYS _ 7 _ 6 _ 4 _ [200]
Data in [ ] is just a reference		Refer to EVM GUIDE:
How to auto detect ringback tone cycle
For code of directly pick upADM _ 5 _ 9907 _ [ 6 ]Function code of directly pick up is
6
Waiting time for ID codeADM _ 5 _ 9908 _ [ 2000 ]Delay 2 sec before detecting ID code
Prefix number of Mailbox ID codeADM _ 5 _ 9920 _ [ Function cod ]Refer to PBX Programming

PBX PROGRAMMING:
Programming Item [ 01.EXTENSION ]:
                              1. enter Extn of  EVM
                              2. select PORT TYPE 
                              3. set to VM

Programming Item [ 06.EXT APPLICAT ]:
                              1. TENANT 1 
                              2. EXT HUNT GROUP :  enter 01 
                              3. UCD ATTRIB : select UCD
                              4. MEMBER1: enter Extn of  EVM PORT1
                              5. MEMBER2 : enter Extn of  EVM PORT 2 
                              6. MEMBER3 : enter Extn of  EVM PORT 3 
                              7. MEMBER4 : enter Extn of  EVM PORT 4
                              8. UNT METHOD : set to LINE

Programming Item [ 06.EXT APPLICAT]:
                              1. VM HUNT CROUP : enter 01
                              2. ICM VM : set to Prefix number of Mailbox ID code 
                              3. BUSY FWD : set to busy identified code
                              4. NO_ANS FWD : set to no-answer identified code
                              Example :
                                            If ICM VM is set to [ 40 ], then set EVM Programming ADM _ 5 _ 9920 _ [ 40 ]
                                            If BUSY FWD is set to [ 41 ], then set EVM Programming SYS _ 6 _ 4 _ [ 4102 ]
                                            If NO_ANS FWD is set to [ 42 ], then set EVM Programming SYS _ 6 _ 3 _ [ 4202 ]

Programming Item [ 02.TRUNK LINE ]:
                               1. TRUNK LINE : enter trunk number
                               2.  select DAY1 RING
                               3. MEMBER 1 : enter 430

OPERATOR PROGRAMMING :
1. press [ FUNCTION KEY ] + # + 0 
2. TENANT GROUP : enter 1 
3. PSWD : enter PASSWORD 
4. CFW AUXI LAMP 
5. ALL EXT SET TO N
                             
 SET  NO ANSWER AND BUSY FORWARD TO [ 430 ] for ALL EXTS